Syed Jahanzaib Personnel Blog to Share Knowledge !

December 9, 2011

Howto Crack Mikrotik 3.30 [P.C.C SUPPORTED VER] [For Educational purpose only]


~ Article by Syed Jahanzaib ~

Crack Link for Mikrotik  3.30 have been Removed on Community Request ! 22/2/2013

I personally condemn usage of illegal/cracked version of MIKROTIK or any licensed software. I highly recommend that if you are using it just for learning purpose then its ok, otherwise if you are using it in commercial environment, then Please, Please, Please BUY it from the Mikrotik/Author WebSite. There are some grey area arguments you can make when using unlicensed software as an hobbyist individual or poor college student, but if you’re a commercial entity making money from said software, then you have little ground to stand on.

While I don’t have any problem when some very low sized network or individuals use unlicensed software when they can’t afford them.

I’m personally not comfortable stealing software and it was one of my reasons to eventually move on to Licensed Versions. I’d rather not use a program at all or get by with a more restricted free version than pirate it. I would consider making an exception for tools that are outrageously expensive for an individual, like most of Microsoft’s  products, but only with the understanding that if a person makes money using those tools, they should eventually pay for them instead of riding the free piracy train.

Anyhow ‘usage of pirated software’s’ talk will never gonna end, we should get down to our business ;) This guide will demonstrate how-to crack Mikrotik ver 3.30  >> (This version supports PCC) Hmmmmmmm

Crack Link for Mikrotik 3.30 have been Removed on Mikrotik Community Request ! 22/2/2013

 

Regard’s
SYED JAHANZAIB

About these ads

129 Comments »

    • I HAVE PROBLEM
      THE INFORMATIONFOR ERROR LIKE THIS :
      /DEV/HDA NO SUCH DEVISE OR ADDRESS…..

      Comment by LIONAIR — June 18, 2012 @ 11:28 PM

      • test / dev / hdb or / dev / hdc depending on where you connected the hard disk, if the ide 1 or 2 on the motherboard

        Comment by fedelviejo — September 10, 2012 @ 3:52 AM

  1. Zaib bhai, did you try to upgrade it to version 4.x? as i tried once last month but it give me some error that key pattern in 4.x is change etc…

    If you tried it then please share with us..

    thanks

    Comment by Arbab — December 26, 2011 @ 1:26 AM

    • I guess it will not work with 4.x
      because till ver 3.x , key was in 7 digits,
      but from upwards, key changed into 8 key digit, so it may not work.

      Comment by Pinochio~:) — December 26, 2011 @ 10:39 AM

  2. zaib bhai i face a problem with cracking MT i successfully add file keygen.npk in mikrotik but when i do ssh with this ip 192.168.2.1 an error appear NO ROUTE FOR HOST…… What should i do now i newbie in mikrotik

    Comment by Mobeen — January 6, 2012 @ 8:31 PM

    • What IP you have set on your mikrotik lan interface?
      What ip you have set on the pc from where you are using ssh ?

      both must be on same subnet.

      Comment by Syed Jahanzaib / Pinochio~:) — January 6, 2012 @ 8:53 PM

      • salam,
        bhia i have problem in my ip address that time i write in ssh with my ip address 192.168.1.66 this my pc ip and my mikrotik ip is also 192.168.1.66 both r same but still massage written is connection refussed pls can u tell me bhia what can i do only problem this
        all i do what u telling in your video but this is the problem here pls help me ass soon as possible

        Comment by khalid khan — February 27, 2012 @ 2:09 AM

      • connection refuse error occurs when you haven’t uploaded the keygen or after up[loading, you haven’t rebooted the mikrotik.

        Comment by Syed Jahanzaib / Pinochio~:) — February 27, 2012 @ 8:34 AM

  3. on MT 192.168.2.1 and on pc 192.168.2.1 defult gatway ……

    Comment by Mobeen — January 7, 2012 @ 12:25 AM

  4. Ether1 192.168.2.1 this is my builtin lan card ip and my exrta lan card ip is not assign yet……

    Comment by Mobeen — January 7, 2012 @ 12:29 AM

    • are you able to ping mikrotik lan ip from your pc ? if not , check the networking setting of mikrotik and your pc. its ip related issue solve it at ur end.

      Comment by Syed Jahanzaib / Pinochio~:) — January 7, 2012 @ 10:38 AM

  5. ping OK i changed my lan card preference ssh done..!
    Now i’ve problem with roskey /dev/hda HU6I-XPT this commad when i enter this command : /dev/hdb: NO SUCH DEVICE AND ADDRESS

    :-( Plz help

    Comment by Mobeen — January 7, 2012 @ 4:12 PM

  6. thanks god i finally completed my 5steps like ur post shows…. Now step 6 is not done bcoz when i import the key which i download from ur given link he said invalid key.. Coz in keygen folder the file with HU6I-XPT this name and my software id name is different my software id is VLHH and something plz help me out with this THANKS

    Comment by Mobeen Ahmad — January 7, 2012 @ 10:20 PM

    • It means you haven’t completed the “SSH TO EXECUTE KEYGEN” process completely.
      do it again untill you see “Work Fine !!!” and then re-check license key which must match to the key provided with keygen.

      Comment by Syed Jahanzaib / Pinochio~:) — January 8, 2012 @ 12:47 PM

  7. Thanks for a great article, I will soon be installing again Insha Allah. but just to add my personal experience here… I tried this very same method few months back and it never worked. Then after completing the SSH step I switched of the router directly instead of rebooting and then the rest worked fine. because after every “reboot” mikrotik always showed the system generated key instead of the crakced key… Has any one else had the same problem.

    Comment by Nabeel — January 10, 2012 @ 6:32 PM

  8. @nabeel
    dont restart mikrotik/router after ssh… when he shows WORK FINE open winbox and import kegen its work fine with me :-) thanks 4 zaib bhai

    Comment by Mobeen — January 11, 2012 @ 9:00 PM

  9. thanks .. Actually as i mentioned… I tried this technique few months before. I saw it on youtube. but after every time when the router displays “work fine” message. I Rebooted from Winbox and after restart the key never worked.. and License was reset again to the one generated at installation. so i googled and found out that you are not supposed to restart.. but Switch it off directly.. then turn back on and then import license key.. and it worked .. So when i saw this blog post i instantly remember what i encountered and thought may be i should share here.. I have one now installed and cracked to level 6 :) it’s in testing phase ..4 WAN PCC method thanks to zaib bhai.. it will be in production environment soon Insha Allah.. JAZAKALLAH

    Comment by Nabeel — January 12, 2012 @ 12:48 PM

  10. sir would you like to tell us that if we forget the password how we can get it full control admin password please help me

    Comment by ijaz — January 14, 2012 @ 12:29 AM

  11. hello mr. zeib, just curious. is that work fine if i clone the hd after the crack proccess finished? can i clone that hd to another hd?

    Comment by mbahsimak — January 18, 2012 @ 3:57 AM

    • I haven’t checked it with any DISK IMAGING application,
      However Mikrotik officially states that if you use disk cloning , Key will lost.

      Any how try it and let us know.

      Comment by Syed Jahanzaib / Pinochio~:) — January 18, 2012 @ 10:32 AM

  12. that right mr. zaib, i just tried last night. at first the mikrotik didn’t boot. i tried to install grubb2 on it and success to booting system. but mikrotik said the key expired :)

    Comment by mbahsimak — January 18, 2012 @ 11:42 AM

  13. thx for you tutorial…

    Comment by mbahsimak — January 18, 2012 @ 11:53 AM

  14. can you tel me your cel num or any live ID, i want to talk you thank you sir g….
    my.email obaid301@gmail.com i have some problum when i configure mikrotik… plz sir

    Comment by obaid — February 1, 2012 @ 6:38 PM

  15. whats your e mail

    Comment by obaid — February 2, 2012 @ 4:43 PM

  16. helo sir… can you tel mew how we configure web proxy? plz sir tel me in detail thankx

    Comment by obaid — February 2, 2012 @ 10:44 PM

  17. thanks

    Comment by obaid — February 3, 2012 @ 12:47 PM

  18. sir i need your help regarding mikrotic. it works fine until i crack it. 404 error comes on hotspot

    Comment by waqar — February 7, 2012 @ 9:50 PM

  19. i have windows 7 and on cmd promt under folder keygen when i m typing ssh 192.168.1.2 it says connection refused while i can ping the target machine and also can conect thrught putty on port 22 just getting refused when trying from win 7 commant prompt ssh 192.168.1.2 what is wrong i searched alot what is other way i can run roskey command if this wont connect through ssh what else i should do please reply thanks

    Comment by Wes — February 8, 2012 @ 6:13 AM

    • This error comes when you don’t install keygen npk package properly.

      First upload keygen to Mikrotik Files section (in main / folder)
      then restart Mikrotik,

      After rebooting, try to ssh, it will work.

      Do let me know the status.

      Comment by Syed Jahanzaib / Pinochio~:) — February 8, 2012 @ 9:01 AM

  20. i am trying to ssh from windows 7 command prompt to mikrotik server 3.30 to crack ssh says connection refused while i can connect via putty to target mikrotik server what is wrong with ssh from windows 7 please reply thanks

    Comment by Wes — February 8, 2012 @ 6:21 AM

    • This error comes when you don’t install keygen npk package properly.

      First upload keygen to Mikrotik Files section (in main / folder)
      then restart Mikrotik,

      After rebooting, try to ssh, it will work.

      Do let me know the status.

      Comment by Syed Jahanzaib / Pinochio~:) — February 8, 2012 @ 8:59 AM

  21. salam dear sir i checked and tried several times the exact key npk file i m using mikrotik 3.30 os but when i double clicked on npk key gen file the version f this file says 3.20 is this the problem ? i dont have correct keygen file? or where can i download mikrotik 3.30 os with working cracked or key gen ssh connection still refusing it kindly give me any link to download both mikrotik os with proper key gen files and license file i will very thankful to you. wait for your answer

    Comment by Wes — February 8, 2012 @ 11:48 PM

    • Dear first you have to download 3.2 and crack it, then you will upgrade to 3.30
      follow the article exactly and you will be able to go through correctly.

      Comment by Syed Jahanzaib / Pinochio~:) — February 9, 2012 @ 8:57 AM

  22. Ok thanks my matter resolved i read above your post in detail and followed it thanks for nice post very helpful and genrous of u to share knowledge thanks and best regards

    Wes

    Comment by Wes — February 9, 2012 @ 3:14 AM

  23. dear Syed Jahanzaib i sent you an email on hotmail i will appericiate if you read my email and reply Thanks

    and best regards

    Wes

    Comment by Wes — February 10, 2012 @ 6:33 AM

    • I have replied you accordingly.

      Comment by Syed Jahanzaib / Pinochio~:) — February 10, 2012 @ 8:56 AM

    • I recommend you not block torrent, rather then blocking, Limit there speed
      Blocking is not an good idea. people will always find a newer way, and you have constantly monitor there usage.

      So its best if you limit there speed, or impose daily quota limit.
      or create rule like this, for example if a user uses torrent, his ip automatically gets in “torrent_users_list” for 1 hour, and this address list should be speed limited.

      Comment by Syed Jahanzaib / Pinochio~:) — February 10, 2012 @ 9:10 AM

  24. ok good so how can i create this rule for user who using torrent and his ip automatically gets in torrent_users_list for 1 hour and procedure to limitize the speed as well
    i ll appericiate if you write complete method using winbox interface thanks waiting for your reply.

    Regards

    Comment by Wes — February 10, 2012 @ 9:46 AM

    • sorry bro, i recently joined new company, and its complex environment here, so quite busy in microsoft world now :S
      just looking for another job now.

      Comment by Syed Jahanzaib / Pinochio~:) — February 10, 2012 @ 10:19 AM

  25. ok i can understand so thats mean you wil write it later work hours or never :) ?

    Comment by Wes — February 10, 2012 @ 10:31 AM

  26. When you get time after work hours please reply to this query ok good so how can i create this rule for user who using torrent and his ip automatically gets in torrent_users_list for 1 hour and procedure to limitize the speed as well
    i ll appericiate if you write complete method using winbox interface thanks waiting for your reply.

    Comment by Wes — February 10, 2012 @ 11:07 AM

  27. i am still waiting sir

    Regards

    Comment by Wes — February 11, 2012 @ 7:19 AM

  28. here is my mikrotik login and logout not workin..if i logout the timr is runing till will finished

    Comment by tim dey — February 28, 2012 @ 7:35 PM

  29. installed 2 months ago and successfully cracked! may we ask any other questions regarding mikrotik except cracking?

    Comment by Asgher Ali Qambrani — March 6, 2012 @ 4:48 PM

    • Cracking / Usage of pirated software is not supported.
      I wrote this guide for some education purpose only. So that people can test mikrotik before purchasing.
      So no support for mikrotik cracking.

      Comment by Syed Jahanzaib / Pinochio~:) — March 7, 2012 @ 9:52 AM

  30. Need mikrotik 4.10 roskey or SSTP nkp .Mikrotik 3.33 license key only 7digits but 4.0 to 6++ have 8digits key .if u have 8digits roskey then please mail me or your blog.my mail id tanvir07@gmail.com

    Comment by tanvir — March 19, 2012 @ 7:34 PM

    • no support for mikrotik crack for illegal usage. buy the license , its cheap in price and the developer of mikrotik really deserve some money for there work :)

      Comment by Syed Jahanzaib / Pinochio~:) — March 20, 2012 @ 2:17 PM

  31. aoa jahanzaib bhai kia ap bata sakte hai usb ke throw internet kaise share kare ge ager mikrtoik server user ker rahe ho.
    plz as soon as possible.

    Comment by muhammad nauman — March 28, 2012 @ 12:50 PM

  32. sir main nay hotspot server create kiya hua hai… main nay Server Profile main Login main sirf HTTP chap pr select kiya hua hai… Mere user cookies kay zariye khud he login ho jaatay hain. Main chahta hoon kay WO login page pr id pasword daal k enter hoon
    Sir plzz is ka solution bata dain

    Comment by Owais Malik — April 2, 2012 @ 8:27 PM

  33. I have patched Mikrotik 3.60 on Dell 280 System, I am able to connect using built in NIC , but Mikrotik is showing all NICs as valid NIC but unable to connect on other NIC , need ur help

    Comment by Mudassir Aftab — April 3, 2012 @ 11:45 PM

  34. AOA, Jahanzaib bhai, I’m trying to ssh after installing keygen.npk but getting an Error: Connection Refused.
    Read all the comments under this post. Using windows 7, Is there any Solution for this?

    Comment by Danish Jamil — April 4, 2012 @ 11:29 PM

  35. Asalam o alakum. zaib bhae. i have cracked MT 3.20 with Level 6 licence acording to the steps given and key works fine for 3.20. but when i upgrade it to MT 3.30, its again says key will expire in 24 hours. i used VMware workstation 7. and set VM guest OS and its version to “others”. did i missed something in VM creation? as i tried 2 – 3 times but same result. Help plz

    Comment by Abdur Rehman — April 14, 2012 @ 4:58 PM

    • Using Mikrotik on VMWARE is not the issue. I myself always use it for testing various scenarios. I have not faced this issue. There must be some step you might be missing or doing wrong. Post all your steps in brief here so I can track where you are doing mistake.

      Comment by Syed Jahanzaib / Pinochio~:) — April 14, 2012 @ 7:44 PM

  36. ok. the steps are
    1. Install MT 3.20
    2. set the IP 192.168.1.10, open winbox and copy “Keygen.npk”
    3. ssh 192.168.1.10 and run “roskey /dev/hda NNFT-86N” (level 6 key)
    4. when it say key works fine, i shutdown VM. start it again and key is change now i import the key
    5. reboots it worked for 3.20
    6. now i copy routeros x86-3.30.npk and reboot the VM
    7. after reboot the licence dialog apear which shows “1234-5678″ and gives 24 hour of expire time

    i done it 2-3 times but same result

    Comment by Abdur Rehman — April 14, 2012 @ 7:59 PM

    • Your step no 3 is incorrect.
      The correct key is HU6I-XPT according to the manual.

      Read the article again and again carefully.

      Comment by Syed Jahanzaib / Pinochio~:) — April 14, 2012 @ 8:04 PM

  37. yes there is problem with key NNFT-86N (i used it)
    but this key “NNFT-86N” is also a level 6 key
    and 3.20 works fine with it
    why upgrade does not work???

    Comment by Abdur Rehman — April 14, 2012 @ 8:30 PM

  38. Creak expire after 4-6 months ………. any solution …..????

    Comment by smn4all — April 19, 2012 @ 9:21 AM

  39. Below is the result when I tried to secure shell to the Mikrotik IP
    ———————————————————-
    C:\> cd \keygen

    C:\Keygen>ssh 192.168.2.1
    connect: Connection refused

    C:\Keygen>ssh 192.168.2.1
    connect: Connection refused

    Comment by Dipson — April 25, 2012 @ 7:10 AM

    • This only happens when you don’t upload KEYGEN.NP to Mikrotik FILES section. (in root folder)
      After uploading, a Reboot is must. Reboot manually from mikrotik server console. You will see INSTALLING KEYGEN .NPK bar. I have updated the article as well with the image, Kindly go through with he tutorial again. Read it carefully.

      Comment by Syed Jahanzaib / Pinochio~:) — April 25, 2012 @ 10:50 AM

  40. This licence doesnt allow superchannels ?.

    Comment by Alfa — April 25, 2012 @ 9:48 PM

  41. Reblogged this on SHERY's BLOG ON COMPUTER NETWORKING/I.T TIPS.

    Comment by Shery — May 19, 2012 @ 5:48 PM

  42. i have been succesfully installed MT using the tutorial on my PC. However, I dont find the user manager package on the machine. can anyone help me how to install it>

    Comment by aplikomstie — May 25, 2012 @ 6:42 PM

  43. I just discovered that hotspot users time still reading even after logout. how will I stop it? please.

    Comment by Greg — May 27, 2012 @ 9:07 PM

  44. i have a seperate pc working as Mikrotik server with ide hard disk…..when i write “roskey /dev/hdb HU6I-XPT” a msg says : /dev/hdb: No such device or address…???!?!!!!

    Comment by Leado — May 27, 2012 @ 9:36 PM

    • NOTE: Various harddisk have different code as below (Adjust it according to your harddisk chemistry)
      hda= HD Virtual
      hdb= HD IDE
      sda= HD sata

      There are other codes too, search google, also probably your hdd is not being detected by the ROS

      Comment by Syed Jahanzaib / Pinochio~:) — May 28, 2012 @ 8:49 AM

  45. i dont really know where to start if i want to connect through ssh to mikrotik. its command promt on PC or mikrotik and how?

    Comment by blair mease — May 31, 2012 @ 11:57 AM

  46. i tried open commad promt and try to type keygen doesnt work

    Comment by blair mease — May 31, 2012 @ 12:03 PM

  47. hi Syed Jahanzaib,

    I just discovered that hotspot users time still reading even after logout. how will I stop it? please.

    I am using mikrotik version 3.20, because I upgrading it to ver.3.30 and I had problem with radius server, “” radius server not responding”” I re-installed the Userman-3.30 and the problem persist, I have to downgrade to 3.20 everything work fine, but the hotspot users time still reading even after logout form the hotspot interface.

    Comment by Greg — June 5, 2012 @ 7:27 PM

  48. i can’t import key. help me

    Comment by dahlie — June 21, 2012 @ 11:41 AM

  49. i have done it at step work fine ! but after it when try to import license key it gives error “invalid license key” ??

    Comment by Ahmed — June 21, 2012 @ 7:25 PM

    • Please give me the ans. for above issue ” invalid license key?

      Comment by Ahmed — June 22, 2012 @ 4:44 PM

  50. guide is excellent, but rosskey is damn slow :(
    my pc rig is core i3 sandybridge
    4gb ram
    roskey takes almost 4 hours :(

    Comment by Zeeshan — June 24, 2012 @ 2:01 PM

  51. 1 more thing can i use 8digit key with roskey method or not ?

    Comment by Zeeshan — June 24, 2012 @ 2:02 PM

  52. thanks for tutorial on crack mikrotik

    Comment by purnosidi — June 26, 2012 @ 6:22 AM

  53. Reblogged this on PurnoSidi #blog and commented:
    crack mikrotik 3.20

    Comment by purnosidi — June 26, 2012 @ 6:23 AM

  54. how can block https different website in squid

    Comment by kashif lari — July 4, 2012 @ 1:28 AM

  55. Some one plz help i am installing cracked 3.2 microtik os when i am trying ssh 192.168.2.1 on command line it is showing connect : route or host, what should i do plz and plz help me out

    Comment by Jaffar Saleem — July 11, 2012 @ 2:37 PM

  56. assalamu’alaikum, Syed jahanzaib, i have download from : http://204.62.56.64/mikrotik/3.20/mikrotik-3.20.iso and then burning and install, this file unlimited, there is not limited until 24 hours, then still go on with your article, i follow step by step “Howto Crack Mikrotik 3.30 [P.C.C SUPPORTED VER] ” untiil 8 hour not finish. plz help me out

    Comment by magelar — July 15, 2012 @ 7:42 AM

  57. why i have a segmentation fault when i type: /dev/hda HU6I-XPT ?

    Comment by rapper — July 16, 2012 @ 1:38 AM

    • ok problem solved I had a problems with my PC runnig MT. I reinstaled MT on another PC and problem disappear :) sorry for my english ;) I’m Polish

      Comment by rapper — July 16, 2012 @ 2:13 AM

      • problem caused by broken hdd – solved: I reinstall mt on antoher full working hdd and I replaced RAM in PC wich I use for routing and any problems was solved. Again sorry for my english

        Comment by rapper3d — August 21, 2012 @ 9:54 PM

      • great, finally you have manage to solve it :)

        Comment by Syed Jahanzaib / Pinochio~:) — August 22, 2012 @ 9:34 AM

  58. guys enjoy 5.18 cracked iso http://www.wi-net.com.ve/descargas/mikrotik/mikrotik-5.18.iso
    not tested with clients but working.. key file in iso..

    Comment by Zeeshan — July 16, 2012 @ 9:28 AM

  59. g sir yeh level 6 key hai maine vbox p install ker k dekha hai clients k sath nahe is liye maine kaha not tested :)

    Comment by Zeeshan — July 16, 2012 @ 12:27 PM

  60. Sir, asslam o alaikum sir me ne mikrotik 3.3 level 6 ko crack kiya he. Abi jab me ne oss me winbox se ip address enter kiye hein to ARP me osse lan aur wan ko show karna chiye lekin ni show ho rahe hein kiya waja ho sakti he
    lan ip he 6.6.6.6/24
    Aur wan 192.168.1.10/24
    Dns name koi b ni diya he
    Dns primry he 192.168.1.1
    Sec he 0.0.0.0.0
    Aur allow remot koun check he
    gateway he 192.168.1.1 aus ping pe he plz me and send the email on my addres hamrisite@ yahoo.com

    Comment by nasir — July 16, 2012 @ 4:43 PM

  61. JAHANZAIB Sir, Salam,
    Sir i have cracked my MT3.30 using via CD..Live method….
    How to i connect my PC to MT Server and configure the wireless server in MT3.30.
    please help me.. and post your personal Cell# though i contact you in any case of trouble.
    Thanks….
    FARHAN HAMEED, PIPLAN, MIANWALI 0331-7219092

    Comment by Farhan Hameed — July 24, 2012 @ 8:48 AM

  62. But is it possible to use usermanager with this version ie. 3.30? and how do i download usermanager since i can’t find it anywhere on the mikrotik page..thanks

    Comment by max — August 3, 2012 @ 6:24 PM

  63. JAHANZAIB Sir, Salam
    i have rb 433 ah v 3.xx i make it v 6 but loss the key … it give me 24 hour to stop ..how i can make it work again plz help me to not loss my r.b
    even any software any level
    thank u

    Comment by alkhansanet — August 5, 2012 @ 8:23 PM

  64. ssh connect: connection timed out .. Any suggestion for this error

    Comment by Itx Marko — August 6, 2012 @ 6:27 AM

  65. i have to copy keygen.npk to files, and restart mikrotik too.
    but that’s not show on package list.

    and that the reason why the ” ssh ” refused connection.

    and now what should i do sir ?

    Comment by gedebag — August 13, 2012 @ 2:26 AM

  66. dear sir, i have 1 6mb ptcl connection, & 4+4+4Mb, what are the 4 wan setting for Mikrotik 5.4 ver ? and 3.3 ver ?
    kindly also mail me copy of Settings. I shall be very thanks for you…..,
    adeel hafeez

    Comment by adeelhafeez786 — September 18, 2012 @ 11:34 PM

  67. dear sir, i have 1 6mb ptcl connection, & 4+4+4Mb, what are the 4 wan setting for Mikrotik 5.4 ver ? and 3.3 ver ?
    kindly also mail me copy of Settings. I shall be very thanks for your kindness…..,
    adeel hafeez

    Comment by adeelhafeez786 — September 18, 2012 @ 11:35 PM

  68. sir can i have videos of mikrotik in urdu,??? if u have plz upload them and share the link

    Comment by Jawwad Hussain — September 24, 2012 @ 2:01 PM

    • I don’t have mikrotik videos, but there are lot of urdu video of mikrotik videos available at youtube, some of them are compiled using my guides,

      Comment by Syed Jahanzaib / Pinochio~:) — September 28, 2012 @ 9:10 AM

  69. Hello, and thanks a lot for the tutorial.

    I have this problem. I’ve installed MikroTik routerOS 3.20 in a PC (Pentium IV 1,6Ghz, 512MB RAM, 4 PCI 3com ethernet cards, 512MB usb flash drive). The installation runs smoothly, in fact, it detects the Generic MASS STORAGE USB DRIVE as a SATA1 harddrive.

    The actual problem is when I attempt to crack it. Not only it is veeeeery anoying, since takes about 3 hours to do the trick. The problem is that IT DOESN’T WORK. After doing

    —> roskey /dev/sda HU6I-XPT

    I get dhe message WORK FINE! But the license software ID doesn’t change, and I can’t import the cracked license.

    I’ve done this procedure several times, also trying with other licences and mikrotik-3.20 isos. Always the same result.

    What can be happening? Is it because of the usb flash drive? That would be a problem, because I don’t have any IDE/SATA harddrive to use on this.

    It is important to mention one thing; when doing roskey, it doesn’t detect the harddrive features (Model, Fw, SerialNo); giving this on screen.

    —> Model=, FwRev=, SerialNo=

    Should I use another usb flash drive?

    Thanks again.

    Comment by Juan Jose Bora — October 3, 2012 @ 6:48 PM

    • Why you are still stucking withe the old 3.3x version.
      ver 5.18 and 5.20 crack is out there. search google, it comes precracked, just import the key and thats it.

      Comment by Syed Jahanzaib / Pinochio~:) — October 5, 2012 @ 8:21 AM

      • Hi, and thanks a lot for the answer. I first tried 5.18, but I’ve ended up with the same problem. After the installation, the softwareID is completely different from the cracked key provided. I’ve tried everything but no cigar. That’s when I figured out that a manual cracked version, such as 3.3x might work. I was wrong.

        The funniest thing is that after spending three days struggling I’v given up and thought of pfSense. I’ve installed pfsense and I’m having a wide variety of problems as well.

        I think is time to surrender and buy a propper RouterBoard with a legal license.

        Thanks a lot though…

        Comment by Juan Jose Bora — October 7, 2012 @ 8:12 PM

      • nowa days, Mikrotik 5.18 and 5.20 crack is available all over the internet. and there is no need to use crack on it. Simple importing the key (along with the pre cracked pacakge) is enough., instant registration :D

        Comment by Syed Jahanzaib / Pinochio~:) — October 9, 2012 @ 4:36 PM

      • But 5.18 or 5.20 cracked when installed doesn’t change the serial number in order to receive the license file. I have already tested, in both versions it works fine when installed in a Hard Disk Drive, but doesn´t work in USB Pendrives.

        Comment by Rodrigo — December 3, 2012 @ 5:42 PM

  70. you’re the one, my online teacher. thank u forever.
    regard from bima indonesia.

    Comment by abunadia29 — October 13, 2012 @ 5:25 PM

  71. hello Sir
    I install Mikrotik and its working but here is a problem. My device signals are Strong but net speed is too slow its show limited or no connectivity. I changed the access point but but the problem is same. I dont know what was the reason. please Sir help me what I do.. zaryabkhan5@gmail.com

    Comment by muhammad atif — December 4, 2012 @ 11:40 PM

    • Its your Wireless issue ….. not a Mikrotik Problem …

      Comment by smn4all — December 5, 2012 @ 9:07 PM

  72. AOA. Good work sir i want to contact you but i haven’t understand you email id.

    Comment by Khuram — January 7, 2013 @ 11:15 PM

  73. AoA.. Sir FIrst of all thanks for detailed discription over it in blog. Second i an having problem that when i installed Mikrotik, and when i goes to crack it i am unable to found any relavent file keygen.npk or anything, as i am unable to have proper crack. can u help me from whwere i can have it, or what should i do!! please respond ASAP.

    Comment by Talha — February 3, 2013 @ 5:56 AM

  74. hello everyone,
    here no keygen file. may be some one delete this file that the link given.
    so anybody give me this files
    thanks

    Comment by ony — February 16, 2013 @ 9:31 PM

  75. i forget my winbox password what i can do

    Comment by asif — April 13, 2013 @ 6:45 AM

  76. i have problem in 5.18 and 5.20 that (found hard drive as ide primary master….) then hang process. please help me….

    Comment by Jamal — February 16, 2014 @ 9:24 AM


RSS feed for comments on this post. TrackBack URI

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

The Silver is the New Black Theme. Create a free website or blog at WordPress.com.

Follow

Get every new post delivered to your Inbox.

Join 2,269 other followers

%d bloggers like this: